Gliderol PURPLE RED (RAL3004) Compact Insulated Roller Garage Door (55mm Lath)

PURPLE RED (RAL3004) Compact Insulated Roller Garage Door (55mm Lath).

Gliderol's Made-to-Measure Compact Insulated Roller Garage Doors are an intelligently designed solution with a 55mm foam insulated lath. This compact roller door is an ideal solution when space above the opening is minimal. The narrower 55mm lath only requires 205mm of headroom.

PLEASE ENSURE YOU HAVE FULLY READ THE 'MEASURING GUIDE' TAB BEFORE PLACING AN ORDER. This is a made-to-measure door, once manufactured, cancellations or returns are not accepted.

Note: All colours have either a RAL code or a British Standard code (BS). Please request a colour sample if you are not sure as digital images are a representation of the colour and will not be an exact match.

Roll-smart automation system:

• Security - The “Keeloq” rolling code technology secures the system from criminal “code cloning”. The risk of another handset using the same code is eliminated as the transmitter uses a different code from one of two billion after every operation. 
• Quiet Operation - Noise is reduced as the motor is housed entirely within the roll of the door giving a quiet and smooth performance.
• Automatic Light - Lights your garage for up to 90 seconds after the motor is activated.
• Roll-smart automation - A slimline aluminium Roll-Smart track fits to the back of the garage door guide. It is incredibly effective and detects obstructions within the doorway, the door reverses automatically should the downward movement be restricted. No more batteries or curly cables. The system uses a standard bottom weather seal without the need for vulnerable electrical contact strips / optical beams inside. The aluminium track is fully sealed to category IP65, and is ultra reliable for trouble free operation year after year. Installation and setup couldn’t be easier. The Roll-Smart track requires a simple 3-wire connection direct to the Slim Line RS-1 control unit. The proven roller door control unit, equipped with reliable microprocessor electronics and extra low voltage control circuits make for complete safety.

Hold-to-Run automation:

• Controllers are to be fitted in a fixed position where you have full sight of the area of the garage door, this is so that you can check that there are no obstacles or persons in front of the door when you operate the system.

Headroom - 55mm foam filled lath, requires 205mm of headroom.

Guides - Supplied with 65mm guides.

Minimum width available for automatic doors is 1100mm.

A Note Concerning Colours: The manufacturing process for the lath profile results in a textured finish, whilst all other coloured items (guides, bottom laths, lock laths, optional fascias and vision panels) are supplied in a satin finish so cannot be guaranteed to match exactly. Over time, some scuffing may occur on front and rear surfaces of doors as a result of their normal operation.

• MEASURING GUIDE for INSULATED 77mm Roller Doors
• FITTING GUIDE for Insulated Roller Doors
• BROCHURE for Insulated Roller Doors.
• ANSA Roll-Smart handset coding.
• Ansa problem solving guide
• Rollsmart install guide.
• DK-14 wireless keypad instructions

Insulated Compact Roller Door (55mm Lath)

PLEASE ENSURE YOU FULLY READ THIS 'MEASURING GUIDE' BEFORE PLACING AN ORDER

This is a made-to-measure door, once manufactured, cancellations or returns are not accepted.

You can install an Insulated Roller Garage Door door either in-between the garage brickwork or behind the reveal. The design of this type of door means the width is the same all the way from bottom of the guides to top of the endplates (box) which sits in line with the outer edge of the guides.

Gliderol insulated roller doors by virtue of their construction require space above the lintel to conceal the rolled up section of the door. The headroom required is 205mm. If recommended headroom is not available this door may still be installed, however some loss of opening height will occur and the box will be visible.

Measuring the Height for ordering:

• The Ordering Height refers to the height of the side guides NOT including the Curtain Roll/Box above this height.

Measuring the Width for ordering:

• The Ordering Width for compact insulated roller doors refers to the full width of the curtain required plus the width of the guides.
• 130mm (2x 65mm guides.

Fitting IN-BETWEEN the reveal brickwork:

Measure the structural opening of the garage door, take the width measurement in 3 places, across the top, middle and bottom. You should use the shortest measurement then take a little more off to allow for fitting tolerance (usually about 15mm). This would be your ordering width.

Then measure the height from the floor to the underside of the lintel in 3 places taking the shortest measurement. Then minus 205mm for the box and minus an extra 10mm or so for fitting tolerance. This would be your ordering height.

Fitting BEHIND the reveal brickwork:

Measure the structural opening of the garage door, take the width measurement in 3 places, across the top, middle and bottom, take the widest dimension. Then add the width of the guides (130mm for doors up to 2600mm wide). This should be your ordering width. If you want part of the guides to be visible on the outside of the door simply reduce the ordering width accordingly. 

Then measure the height from the floor to the underside of the lintel. If you have enough headroom above the lintel, between the lintel and the ceiling (205mm), this would be classed as the ‘guide height’ (ordering height). 

If you don’t have at least 205mm headroom between the lintel and ceiling for the box, you can still order the door but the drive through height would be reduced. In this instance measure the height from the floor to the ceiling in a few places taking the shortest measurement. Then minus 205mm for the box and an extra 10mm or so for fitting tolerance. This would be your ordering height.

Garage Doors - UK mainland delivery only, excludes certain Scottish Highland postcodes. Please ensure the road access is suitable for a Heavy Goods Vehicle and there is suitable space to park safely to offload your door.

We operate a 1 driver delivery service. Our driver will require assistance from someone able-bodied to help unload the door to an appropriate place which is not an excessive distance from the delivery truck.

Garage Door Parts - are dispatched within 1 working day and delivered by DPD or Royal Mail.

Single Skin Roller Doors - usually delivered within 5 - 14 working days by our inhouse team of delivery drivers.

Insulated Roller Doors - usually delivered within 5 - 14 working days by our inhouse team of delivery drivers.

Up & Over Doors - usually delivered within 6 weeks by our inhouse team of delivery drivers.

Side Hinged Doors - usually delivered within 8 weeks by our inhouse team of delivery drivers.

Insulated Side Hinged Doors - usually delivered within 8 weeks by our inhouse team of delivery drivers.

Sectional Doors - usually delivered within 8 weeks by our inhouse team of delivery drivers.

Industrial Sectional Doors - usually delivered within 6 weeks by our inhouse team of delivery drivers.

Entrance Doors - usually delivered within 2 weeks by our inhouse team of delivery drivers.

Fire Doors - usually delivered within 4 weeks by our inhouse team of delivery drivers.

Gates - usually delivered within 3-4 weeks by our inhouse team of delivery drivers.

Returns

All garage doors are made to order. Once manufactured cancelations or returns can not be accepted.